Posted on

seeds to kill weeds

When you cut slits in the landscape fabric and install new plants, be careful that you don’t get dirt all over the landscape fabric. After all, why prepare a home for airborne seeds? Sure, you will be applying mulch. But airborne weed seeds can wend their way through mulch particles. If they find dirt, then they are “weeds waiting to happen.”

Run a mower over the land to reduce the weeds’ height further. Now that all the weeds are as short as possible and the stumps have been removed, rent a large tiller to uproot all the weeds. Since this plot of ground is uncultivated soil, you will need a tiller that has some power: Do not undertake this task with a small garden cultivator! Allow the tiller’s tines to dig deep enough into the ground to loosen the weeds, so they can be removed—roots and all, if possible.

If there are shrubs and trees present, cut them down with an ax or chainsaw. The ground needs to be smooth before you begin soil solarization (since you will be spreading plastic over it), so you will also have to remove the stumps left behind. If you are looking for a cheap way, use a tool called a “mattock.” Dig and chop your way with the mattock under the root-ball to access and remove the taproot. Warning: this is hard work and may be feasible only for smaller stumps.

Preparation

Now you truly have a “clean slate” with which to work. Remove the plastic and lay down landscape fabric. You should try to use one of the stronger types of landscape fabric if possible, just in case—in spite of your best efforts—any sharp objects remain in the ground (which would puncture the landscape fabric).

See also  2 pounder weed seeds

Cover the raked, moistened area with a clear polyethylene sheet. The edges of the sheet can be held down by cinder blocks to keep the plastic from blowing away. If the raking mentioned above was done diligently enough, there will be no sharp objects sticking up to puncture the plastic. The sheet of clear plastic can be anything from 1 to 6 mil. in thickness. In the Northern hemisphere, the best time for soil solarization is June and July, when the sun is at its peak. UIE recommends keeping the sheet of clear plastic tightly stretched out over the area for about 2 months. During that time, the sun will be killing weeds for you—”cooking” them before they have a chance to sprout. Plant pathogens will be killed, to boot.

Now use a steel rake on the area that you have just tilled, wielding it like a fine-toothed comb to remove the majority of the uprooted weeds. Next, rake the area again, this time with the object of evening out the soil as best you can and removing stones, twigs, etc. The final preparation for soil solarization will require the use of a garden hose. According to the University of Idaho Extension (UIE), you should moisten the area that you have just raked to “conduct and hold heat, to stimulate weed seed germination, and to prevent dormancy of below-ground vegetative plant parts.”

Of course, if you use an organic mulch (such as a bark mulch), it will eventually decompose anyhow, becoming fertile ground for weeds. What can you do? Well, you had better keep new weeds pulled, faithfully. Vigorous roots pushing downwards can stress landscape fabric and breakthrough. On the bright side, these weeds should be relatively easy to pull, since mulch is a lot looser than dirt, and weed roots will not become impossibly entrenched.

See also  jimson weed seed dose

“We focus on killing weed seedlings because we can see them, and we have products available to do this,” Davis says. “Certainly, we don’t want to give up managing weed seedlings, but if we reduce weed seedbank population densities, managing weed seedlings becomes much easier.”

Davis conducted that early research to evaluate a valuable option for growers who want to manage hard-to-control weed populations: Manage the weed seedbank to prevent weeds from getting started.

“I began to measure weed seed predation and saw that within two days, nearly all of the seeds I’d put out in the field [to measure the amount of weed seed predation] would be gone,” says Davis, an ecologist with USDA’s Agricultural Research Service at the University of Illinois. “Over the course of a growing season, I’ve seen weed seed predators eat between 40% and 90% of the seeds produced that year. It’s an important weed management benefit that we take for granted, but which really makes a difference.”

Weed management toolbox

Davis says the most important element of a successful weed seedbank management strategy is to implement a diversified crop rotation so crops with contrasting life histories are grown in different phases of the rotation. “This prevents any one weed species from getting too comfortable, and makes it difficult for weeds to reproduce in the canopy of a crop with a different life history,” he says.

Cover crops can be a tool for weed seedbank management. “Cover crops have had a long history in the Midwest, and can make a comeback should market forces and weed management realities combine to make them necessary,” Davis says. “Adding cover crops to the weed management toolkit can reduce opportunities for weed seedlings to establish, and can also provide a critical delay in weed seedling emergence so that crop competition can further suppress weeds.”

See also  seed weed before snow

The key to weed seedbank management is to reduce the ability of the seeds to germinate. Then growers either don’t have the weeds to control or they have fewer weeds to handle with other weed management tools. Here are Davis’s suggestions for managing a seedbank:

As a graduate student, Adam Davis spent his Septembers crawling around on his hands and knees through crop fields trying to find and recover giant foxtail seeds for his research studies. He soon discovered that seed predators had already eaten the seeds on the soil surface. Mice, crickets, ground beetles and other organisms were doing a highly effective job at reducing the number of weed seeds.